What does the Porsche VCI diagnostic interface include?
VCI BOX
2.TECHNICAL DATA OF THE DIAGNOSTIC INTERFACE PT3G-VCI
Module interface: mini USB socket
Power consumption: approx. 5W in operation
Storage temperature: -20 ° C… + 85 ° C
Operating temperature: -20 ° C… + 40 ° C
Power supply: 8 … 18V via diagnostic interface (OBD)
Power consumption
with WLAN module
via diagnostic interface
Normal operation: 300mA / 13.8V,
Shutdown stage 1: 250mA / 13.8V
Shutdown stage 2: 5mA / 13.8V
RAM: 256MB DDR RAM
Permanent memory: 16MB NOR, 4 GB NAND flash
Dimensions: 110 x 48 x 25 mm (LxWxH)
Weight: 90 g
Vehicle interfaces:
High speed CAN
according to ISO 11898-2 o CAN 2.0B with 11- and 29-bit identifier
maximum data rate 1Mbit / s
Low speed CAN
maximum data rate 125kbit / s
-according to ISO 11898-2 ? Vehicle Ethernet
according to ISO 13400
maximum 100Mbit / s
Ethernet activation switchable
K line
for 12V vehicle systems
according to ISO 9141-2 (max.sink current 300mA)
maximum data rate 125kbit / s
510 ohm line pull-up (can be deactivated)
KL30 voltage measurement
KL15 voltage measurement
Voltage measurement at pin 8 and 9 of the diagnostic connector
3.WLAN MODULE
With the WLAN module, the PT3G-VCI is able to establish a direct connection via the WLAN interface to the diagnostic device or to the corresponding infrastructure of the workshop network. For this The WLAN module supports the modes infrastructure and direct connection (WLAN access point).
TECHNICAL DATA OF THE WLAN MODULE
Network interface: WLAN 802.11 a / b / g / n 2T2R 300Mbit / s, 2.4 GHz and 5 GHz
Client mode (WPA2-PSK, WPA2-EAP / TLS)
AP mode (WPA2-PSK)
VAS interface: mini USB plug
Storage temperature: -20 ° C… + 85 ° C
Operating temperature: -20 ° C… + 40 ° C
Dimensions: approx. 46 x 48 x 25 mm (WxDxH)
Weight: 22 g
DIAGNOSTIC DEVICE SYSTEM REQUIREMENTS
For the diagnostic device with which the PT3G-VCI is to be configured via the base station
the following system requirements are met:
Operating system: Windows 7, 8.1 (32 & 64 bit)
PIWIS Tester III
Interfaces: 2 x USB 2.0 (or higher, see PIWIS Tester III)
4.BASE STATION
The base station is used to configure and self-test the PT3G-VCI. It is connected to the diagnostic device using the included Y USB cable.
The base station has 4 green LEDs on the top.
TECHNICAL DATA OF THE BASE STATION
Diagnostic device interfaces: USB 2.0 high speed, 480Mbit / s
(Need two USB interface data cables to provide power)
VCI interface: diagnostic socket
Power consumption: Without PT3G-VCI: 0.25W
with PT3G-VCI: 5W
Storage temperature: -20 ° C… + 85 ° C
Operating temperature: -20 ° C… + 40 ° C
Dimensions: 80 x 90 x 36 mm (WxDxH)
Weight: 146 g
PIWIS III with Piwis 3 Software Details:
1. Software Version:
Dual System: V40.600 + V38.200
V40.600(with Engineering software support online programming,but you should have an online account)
V38.200(with Engineering software support offline programming)
NOTE:
Lenovo Yoga with Dual system in one SSD, one system sofware is V40.600, another is V38.200, when your start the laptop, choose one software that you need, both software can be used.
2. Functions: Diagnosis and Programming
3. Update: By SSD
4. Connection: Via USB or Wifi
5. Support Vehicles: Support all Porsche till 2021
6. Password for Laptop: 123456
7. Multi-Language: German, English, US English, French, Italian, Spanish, Japanese, Chinese, Russia, Portuguese, Nederlands
Piwis III Supports New & Old Cars:
All Porsche from 1998-2021:
1.Porsche 911(997) (991)
2.Boxster/Cayman (987)
3.Cayenne up to MY 2010
4.Cayenne from MY 2011
5.Panamera
Especially the latest models:
1.Paramera (971) 2021
2.Caynenne (92A) 2021
3.Macan (95B) 2021
4.911 (991) 2021
Also support All Other Old car models
Piwis III Details at www.cnautotool.com